[Jan-2023] HP HPE0-V14 Actual Questions and Braindumps
Pass HPE0-V14 Exam with Updated HPE0-V14 Exam Dumps PDF 2023
How much HP HPE0-V14: Building HPE Hybrid IT Solutions exam cost
HP HPE0-V14: Building HPE Hybrid IT Solutions exam cost is $110, for more information please visit Official Website.
NEW QUESTION 91
You are configuring an MSA 2052 for one of your customers in OCA.
Click on either one of the two places on the Bill of Materials screen that will enable you to verify the configuration and get details on any errors.
Answer:
Explanation:
NEW QUESTION 92
A customer needs to locate an exact time when a link down event occurred at the FC port of Nimble storage Which on-premises tool can the customer use?
- A. Embedded UEFI Diagnostics
- B. HPE InfoSight
- C. HPE StoreServ Management Console
- D. HPE Nimble Storage web-based user interface
Answer: B
NEW QUESTION 93
Which protocol should be used to access an exported directory on a network-attached storage device?
- A. SNMP
- B. BGP
- C. RIP
- D. NFS
Answer: D
NEW QUESTION 94
You are troubleshooting server issues and need to troubleshoot when online and offline.
Which HPE tool should you use?
- A. Integrated Management Log
- B. Insight Remote Support
- C. Active Health System
- D. Insight Diagnostics
Answer: D
NEW QUESTION 95
Match the Networking Product Family to the appropriate use case:
Answer:
Explanation:
NEW QUESTION 96
You are reviewing a series of MSA2052 storage designs for a customer's remote locations. Their largest
remote site requires the highest possible level of internal data protection with at least 20 TB of storage. Which disk drive design is adequate for this site?
- A. 8 HPE MSA 2 TB drives, configured with RAID5
- B. 10 HPE MSA 2 TB drives, configured with RAID0
- C. 14 HPE MSA 2 TB drives, configured with RAID1
- D. 12 HPE MSA 2 TB drives, configured with RAID6
Answer: D
NEW QUESTION 97
You are installing a server solution in a customer's data center.
How can you ensure that the installation complies with relevant electrical best practices? (Choose two.)
- A. Configure the server power to a single electrical circuit in the data center
- B. Balance the server power load between available AC supply branch circuits
- C. Do not allow the overall system AC current load to exceed 80% of the branch circuit AC current rating
- D. Use fanout cables when connecting the server to the network for maximum electrical impedance
- E. Use a single-phase, two-wire power receptacle with protective earth or ground (PE) to filter interference from the power grid
Answer: B,C
NEW QUESTION 98
A customer is considering an upgrade of their network, which connects 10 servers. The customer has a converged data center networking architecture with Layer 2 and Layer 3 functionality. Which HPE product family will meet this customer's needs?
- A. Altoline
- B. FlexFabric
- C. Arista
- D. Aruba
Answer: B
Explanation:
B
NEW QUESTION 99
A customer is subject to regulatory requirements and their data is highly sensitive.
Which HPE Smart Array feature addresses their need for an additional level of security for data stored inside their server?
- A. Rapid Parity Initialization
- B. Smart Battery backed-up write-cache
- C. Secure Encryption
- D. SmartCache
Answer: D
NEW QUESTION 100
Refer to the exhibit.
A customer needs a server with four 10Gb network adapters. They need it to be configured for the best possible network throughput.
Given the BOM in the exhibit, what do you need to add to this server to meet the customer requirement?
- A. SSD Drives
- B. Smart Storage Hybrid Capacitor
- C. Secondary Riser Kit
- D. Workload Accelerator
Answer: D
NEW QUESTION 101
Match the customer requirement to the appropriate HPE storage solution.
Answer:
Explanation:
Reference:
https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA5-6078ENW.pdf https://assets.ext.hpe.com/is/content/hpedam/a50002410enw
NEW QUESTION 102
In which layer of the OSI model would you find an IP address?
- A. Physical
- B. Data link
- C. Network
- D. Application
Answer: C
NEW QUESTION 103
A customer needs to enable HPE Proactive Care and automated case creation for server hardware failures in their OneView environment.
Which step do you need to complete in OneView to accomplish these tasks?
- A. Enable remote support from the Settings page.
- B. Add the hosts to the managed devices group.
- C. Configure proactive scan reports.
- D. Apply the OneView Advanced monitoring license.
Answer: A
NEW QUESTION 104
Refer to the exhibit.
A customer needs a server with four 10Gb network adapters. They need it to be configured for the best possible network throughput.
Given the BOM in the exhibit, what do you need to add to this server to meet the customer requirement?
- A. SSD Drives
- B. Smart Storage Hybrid Capacitor
- C. Secondary Riser Kit
- D. Workload Accelerator
Answer: D
NEW QUESTION 105
A customer needs a solution for a rack of servers. They need connectivity for 14 HPE DL380 servers, which each have two 10-GBASE-T Ethernet ports, and 10 HPE DL360 servers, which have two 10GBASE-X SFP+ Ethernet ports.
They need switch redundancy for each server and want to connect all servers to the same switch stack. The client also needs a 400 Gb backbone connection to the data center core switch from the solution you are creating.
Which architecture meets the customer requirements?
- A. One VSX stack of two Aruba 8325 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch - B. One IRF stack of wo HPE 5945 2-Slot switches each with the following: One 24-Port SFP28 + 2-Port QSFP28 module One 24-Port 1/10GBASE-T + 2-Port QSFP+ module 10 SFP+ to SFP+ DACs in each switch
- C. One IRF stack of two HPE 5945 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch - D. One VSX stack of two Aruba 8320 48-port 1/10GBASE-X SFP+ switches with the following: 14 10GBASE-T transceivers in each switch
10 SFP+ to SFP+ DACs in each switch Two QSFP+ to Quad SFP+ adapters
Answer: C
NEW QUESTION 106
Match the HPE Tool with its use case. Select all that apply.
Answer:
Explanation:
NEW QUESTION 107
A customer needs to deploy an application on a newly-installed HPE ProLiant server, but they report that the server is not online. They call you for remote support. The IP address on the production network cannot be reached. You are evaluating the probable root causes of this issue.
According to the troubleshooting methodology, what are next two steps? (Select two)
- A. Use Microsoft Remote Desktop or VNC to check the server's NIC and IP address configuration
- B. Run insight Diagnostics on the Server
- C. Use OneView to see f the server firmware is up-to-date
- D. Log in to iLO to see if the server hardware and NIC are online and configured correctly.
- E. Remote console into the ToR switch to check the server's port configuration.
Answer: B,D
NEW QUESTION 108
Refer to the exhibit.
You are configuring a pair of HPE 5945 switches into an IRF stack You have cabled the switches as depicted in the exhibit Into which IRF Ports should you place each switch interface?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: C
NEW QUESTION 109
Match each workload profile description with the corresponding profile. (Select all that apply.)
Answer:
Explanation:
Explanation
Missing Critical - Large number of database operations (Trades Performance reliability) Transactional Application Processing - Trades performance for reliability (Large number of DB Operation) General Peak Frequency Compute - Maximize processor speed
NEW QUESTION 110
You need to update the firmware on an MSL2024 to version 26.43.51. Which HPE utility do you need to use?
- A. Smart Storage Administrator
- B. OneView Standard
- C. Library & Tape Tools
- D. Central Management Console
Answer: C
NEW QUESTION 111
A Nimble storage customer is experiencing rapid data growth and needs to scale their storage resources.
Which action should the customer take first?
- A. Access the SSMC for upgrade advice
- B. Access Smart Storage Administrator to configure additional storage resources
- C. Access InfoSight for recommendations
- D. Access the clustering feature in the CMC to configure active/active clustering
Answer: C
NEW QUESTION 112
You are installing multiple components into an existing server.
Which HPE resource can you use to verify the compatibility of the server hardware options with the server?
(Select two.)
- A. Server User Guide
- B. Smart Selling tool
- C. Quickspecs
- D. SPOCK
- E. iQuote Universal
Answer: A,D
NEW QUESTION 113
In which protocol are REST API requests transported?
- A. SSH
- B. CRUD
- C. HTTP
- D. SOAP
Answer: C
Explanation:
Reference: https://techhub.hpe.com/eginfolib/servers/docs/HPRestfultool/iLo4/data_model_reference.html
NEW QUESTION 114
......
Latest HPE0-V14 Pass Guaranteed Exam Dumps with Accurate & Updated Questions: https://actual4test.practicetorrent.com/HPE0-V14-practice-exam-torrent.html