Oct-2024 EMC D-PEMX-DY-23 Actual Questions and Braindumps
D-PEMX-DY-23 Dumps To Pass EMC Exam in 24 Hours - PracticeTorrent
NEW QUESTION # 33
When a SAS IOM is power cycled, how much time does it take for the storage-IOM to display mapping information?
- A. 300 seconds
- B. 500 seconds
- C. 400 seconds
- D. 600 seconds
Answer: A
NEW QUESTION # 34
Which command(s) is supported in the current PowerEdge MX Redfish implementation?
- A. HEAD and PUT
- B. GET and DELETE
- C. PUT and DELETE
- D. PUT only
Answer: B
NEW QUESTION # 35
What item is used to refer to a daisy-chained configuration of a multiple MX7000 chassis environment?
- A. Identity group
- B. Chassis group
- C. Wired group
- D. Physical group
Answer: C
NEW QUESTION # 36
What is the port configuration of the MX9116n FSE?
- A. 32 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - B. 32 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - C. 16 internal 25 GbE server facing ports
10 QSFP28-DD ports
4 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports - D. 16 internal 25 GbE server facing ports
12 QSFP28-DD ports
2 100 GbE QSFP28 uplink ports
2 100 GbE QSFP28 unified ports
Answer: D
NEW QUESTION # 37
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
- A. Enabled by default, all switch-specific OS10EE capabilities are available.
- B. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
- C. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
- D. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
Answer: D
NEW QUESTION # 38
A systems administrator must extract log files from an MX7000. The logs cannot be saved locally and must only be stored on a secure file server.
Which share protocols can they use to save the logs?
- A. NFS and HTTPS
- B. SFTP and CIFS
- C. CIFS and NFS
- D. HTTPS and SCP
- E. HTTPS and SFTP
Answer: C
NEW QUESTION # 39
Which network fabric connects directly to the chassis midplane?
- A. Fabric D
- B. Fabric B
- C. Fabric C
- D. Fabric A
Answer: C
NEW QUESTION # 40
When multiple MX9002m modules are daisy-chained to Top-of-Rack switches, which uplink port can be used for stacking?
- A. Gb1 uplink ports can only stack with other Gb2 ports
- B. Only the Gb2 port on the secondary (right) MX9002
- C. Only the Gb2 port on the primary (left) MX9002
- D. Either uplink port can be utilized
Answer: D
NEW QUESTION # 41
In SmartFabric mode, what is the recommended maximum number of VLANs per server port on an MX7000 switch?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 42
A technician is doing an initial MX7000 setup and wants to use KVM to configure the MM. KVM is not working.
What are the two causes of this issue?
(Select 2)
- A. The resolution set on MM is too high.
- B. Mouse is not connected.
- C. MM is going through a reset.
- D. DP-to-DVI and DP-to-HDMI adapters are not supported.
Answer: C,D
NEW QUESTION # 43
Which uplink configuration combination of the Top of the Rack Switch and the MX7000 Management Module is supported?
- A. 100 Mbps (Auto negotiation OFF) and Auto negotiation OFF
- B. 100 Mbps (Auto negotiation ON) and Auto negotiation OFF
- C. 100 Mbps (Auto negotiation OFF) and Auto negotiation ON
Answer: A
NEW QUESTION # 44
Refer to the exhibit.
A customer recently replaced all the dual-port network cards in mezzanine A with quad-port network cards across all 16 PowerEdge MX740c sleds in the two-chassis configuration. The customer can only access half of the network ports, even though the quad-port cards are visible in the iDRAC.
What actions are required to resolve the problem?
- A. Reboot the switches.
Adjust the switch configuration to use the new ports. - B. Reseat all the switches.
Adjust the switch configuration to use the new ports. - C. Do a virtual reseat of all the MX740c sleds.
Update the firmware on all the quad port network cards.
Adjust the switch configuration to use the new ports. - D. Install a new 200G cable from port 3 on the MX7116n in chassis 2 slot A1 into port 19 on the MX9116n in chassis 1 slot A1.
Do the same for the switches in slots A2.
Adjust the switch configuration to use the new ports.
Answer: D
NEW QUESTION # 45
A customer has an MCM group consisting of four MX7000 chassis. They need to take the lead chassis down to perform maintenance.
How can the customer ensure that another chassis takes over the lead role in the MCM Group?
- A. The MCM group will elect a new lead chassis.
- B. The backup chassis will take the lead automatically.
- C. Promote the lead chassis to a passive chassis.
- D. Promote the backup lead chassis as the new lead chassis.
Answer: D
NEW QUESTION # 46
What is the minimum required HW configuration on the PowerEdge MX840c to POST?
- A. 1 processor in socket CPU2
1 memory module installed in socket B1
1 mezzanine card installed in Mezz B1 slot - B. 1 processor in any CPU socket
1 memory module installed in any socket
1 mezzanine card installed in any Mezz slot - C. 1 processor in socket CPU1
1 memory module installed in socket A1
1 mezzanine card installed in Mezz A1 slot - D. 1 processor in each CPU socket
1 memory module installed per CPU socket
1 mezzanine card installed per CPU Mezz slot
Answer: C
NEW QUESTION # 47
A customer would like to periodically change the iDRAC root password on all the servers in their MCM Group.
What feature in OME-M should they use?
- A. Chassis Deployment Wizard
- B. Resource Pools
- C. Quick Deploy
- D. SupportAssist
Answer: C
NEW QUESTION # 48
Which MX7000 chassis components does the Vertical Power Distribution Board power?
- A. IOMs
Rear fans
Front fans - B. Compute sleds
Right and Left Control Panels
Rear fans - C. IOMs
Compute sleds
Rear fans
Answer: A
NEW QUESTION # 49
What is the maximum supported drive configuration on a PowerEdge MX840c compute sled?
- A. 4 x 2.5" drives and 2 x 3.5" drives
- B. 8 x 2.5" drives
- C. 2 x 2.5" drives and 4 x 3.5" drives
- D. 6 x 3.5" drives
Answer: B
NEW QUESTION # 50
A server sled has a single mezzanine card installed in the correctly supported slot. To which IOM fabric(s) does the sled have access?
- A. Either Fabric A or Fabric B, depending on the configuration set in OME-M
- B. Fabric A1 and Fabric A2
- C. Fabric A1 and Fabric B1
- D. Fabric A1 only
Answer: D
NEW QUESTION # 51
Which two-socket PowerEdge sled can support up to eight E3.s NVMe Gen 5 SSD drives?
- A. MX740c
- B. MX760c
- C. MX840c
- D. MX750c
Answer: B
NEW QUESTION # 52
What are the typical ambient inlet temperature readings that ATMOS hardware and fans support?
- A. 30 uplink configuration combination of the Top of the Rack Switch and the MX70(104°F)
- B. 25°C (77°F), 30°C (86°F), and 35°C (95°F)
- C. 15°C (59°F), 20°C (68°F), and 25°C (77°F)
- D. 20°C (68°F), 25°C (77°F), and 30°C (86°F)
Answer: A
NEW QUESTION # 53
In addition to one compute sled, one management module, and one IOM, what is the minimum required HW configuration on the PowerEdge MX7000 to POST?
- A. 2 power supply units
4 front cooling fans
5 rear cooling fans - B. 3 power supply units
4 front cooling fans
5 rear cooling fans - C. 1 power supply unit
1 front cooling fan
1 rear cooling fan - D. 1 power supply unit
2 front cooling fans
3 rear cooling fans
Answer: A
NEW QUESTION # 54
Which ports will be active in an MX9116n FSE if there are dual-port NICs in all the server sleds?
- A. odd-numbered server-facing ports
- B. server-facing ports 1-8
- C. even-numbered server-facing ports
- D. server-facing ports 9-16
Answer: A
NEW QUESTION # 55
......
Download the Latest D-PEMX-DY-23 Dump - 2024 D-PEMX-DY-23 Exam Question Bank: https://actual4test.practicetorrent.com/D-PEMX-DY-23-practice-exam-torrent.html